Microseven Tech Support

Tech Support

Archive for the ‘Hardware Repairing’ Category

Install SD card on M7-HSDDNWS-26X and M7-HSDDNWS-18X IP Cameras

without comments

Unscrew the front glass, unscrew the black heater and blower ring. Unscrew 4 screw on the frame inside the camera. Disconnect camera and board cable. The SD card is located on the motherboard. See the snapshot in the following:
photo (11)

Written by microseven

March 28th, 2013 at 1:16 pm

M7.R.Radio Directional Outdoor Waterproof Microphone connection configuration

with 2 comments

Here is the connection configuration V-A-G:

V red color
A yellow color
G black color

vag

Written by microseven

January 9th, 2013 at 1:34 pm

M7LIVE v2.10 (Microseven streaming server) released on (7/25/2012)

with 3 comments

M7LIVE v2.10 (Microseven streaming server) released on (7/25/2012)

Release notes:

Fixed bug on streaming video and audio. If you have installed M7LIVE v2.09 or you need audio on the streaming, you must update your current M7LIVE version to M7LIVE v2.10 on your PC or your Windows server. To do it, you need to uninstall it on your current machine, and re-install M7LIVE using M7LIVE v2.10. It can be downloaded from www.microseven.com use your Microseven ID.

Microseven Support

Written by microseven

July 25th, 2012 at 12:45 pm

M7LIVE v2.09 (Microseven streaming video server) released on (6/12/2012)

with 2 comments

M7LIVE v2.09 (Microseven streaming video server) released on 6/12/2012).

Release notes:
1. Add uPnP function. The benefit is that you don’t have to configure port forwarding on router, but you have to use uPnP router. Router will be added port forwarding information automatically after you install the M7LIVE v2.09.
2. Add opening ports and M7LIVE in Windows firewall, you don’t need to go to firewall setting to add ports and M7LIVE in Windows firewall.
3. Add a field for M7LIVE port, default is 7000. You don’t have not modify it unless you use only one PC or server installing M7LVE. Allow you change M7LIVE 7000 port from the second PC or server in the same local network.

Written by microseven

June 13th, 2012 at 12:45 am

Microseven M7CMS for Mac v1.0.2 (release note on 6/10/2012)

with 4 comments

Microseven M7CMS for Mac v1.0.2 (release note on 6/10/2012)

“PRE” for preset position of pan, tilt and zoom setting up on PTZ high speed dome camera.

It has been added an icon on camera in camera list with on/off with crosshair (reticle) OSD (on-screen display) on screen.

Refer to Microseven M7CMS for Mac v1.0.1.

Written by microseven

June 10th, 2012 at 7:15 pm

Microseven M7CMS for Mac v1.0.1 (release note on 5/24/2012)

with 3 comments

M7CMS for Mac 1.0.1 release notes (released on 5/24/2012)

To search camera IP address in local network, and modify camera IP address. To add camera IP address other than local IP address without searching to M7CMS. To view camera video live online using Mac. PTZ functions allow you remotely control pan, tilt, and zoom on Microseven IP cameras (Microseven network cameras). M7CMS is only working for Microseven IP cameras (Microseven network cameras) recently. To be able to edit OSD’ (On-screen display) name, date and time. Allow you to be able to set up camera’s network settings. To be able to change and modify video resolutions, and streaming type which primary and secondary streaming, and quality of video image. The feature of editing bitrate of video streaming is the best in this App. To be able to update new firmware features. To search Wi-Fi AP, allows you enter Wi-Fi encryption key to connect camera wirelessly.

1. Mac OS X 10.6 or greater
2. Only work for Microseven IP cameras (Microseven network cameras)
3. Do search cameras in local network, find cameras and add camera to M7CMS
4. Modify camera IP address
5. Control PTZ in M7CMS to remote camera pan, tilt, and zoom on your Mac working with Microseven PTZ IP cameras (Microseven network cameras)
5. Be able to change and modify video resolutions and update new firmware features.

This released version added audio, wireless/wifi, video and firmware updating functions.

Written by microseven

June 8th, 2012 at 9:12 am

Posted in Apps Upgrade,Hardware Repairing

Tagged with ,

M7 firmware v1.3.8.4 release notes (5/24/2012)

without comments

This firmware updated is added RTSP sound (audio through RTSP). Corrected M7IE spelling error, which use “Signal Strength” instead of “Signal Strenghth”.

Written by microseven

June 4th, 2012 at 11:32 am

Microseven M7CMS Full version 3.455 (released on 5/16/2012)

without comments

Microseven M7CMS Full version 3.455 (released on 5/16/2012)

Fixed one word spelling correction. “Signal Strength”, it was “signal Strenghth”.

Written by microseven

June 4th, 2012 at 11:21 am

Posted in Apps Upgrade,Hardware Repairing

Tagged with

M7LIVE 2.08 (streaming video server on microseven.tv) released on (6/1/2012)

without comments

M7LIVE 2.08 (Microseven streaming server) released on 6/1/2012).
This version released to fix the issue from cameras after it is updated firmware ramdisk-nt3511h-v1.3.8.4,video streaming cannot be played M7LIVE on the website.
Download is available in microseven.com store, you need to use your Microseven ID to download it and update it on your server or PC.

Written by microseven

June 4th, 2012 at 11:05 am

Microseven M7CMS for Mac v1.0.1 (release note on 5/24/2012)

without comments

M7CMS for Mac 1.0.1 release notes (released on 5/24/2012)

1. Mac OS X 10.6 or greater
2. Only work for Microseven IP cameras (Microseven network cameras)
3. To do search cameras in local network, find cameras and add camera to M7CMS
4. To modify camera IP address 5. To control PTZ in M7CMS to remote camera pan, tilt, and zoom on your Mac working with Microseven PTZ IP cameras (Microseven network cameras)
5. To be able to change and modify video resolutions and update new firmware features.

This released version added audio, wireless/wifi, video and firmware updating functions.

Written by microseven

June 4th, 2012 at 10:13 am

Posted in Apps Upgrade,Hardware Repairing

Tagged with ,

M7CMS for Mac is ready for downloading in www.microseven.com

without comments

M7CMS for Mac is ready for downloading in www.microseven.com
Manual for using it will be released.
Mac OS X 10.7 or greater.
Only work for Microseven IP cameras.
To search camera IP address in the local network, find IP address of camera and modify IP address of camera.
PTZ control on Mac OS X to do pan, tilt, and zoom remote Microseven IP dome camera.

Bug report to support@microseven.com

Written by microseven

May 3rd, 2012 at 3:46 am

Posted in Apps Upgrade,Hardware Repairing

Tagged with

M7 firmware v1.3.8.3 release notes

without comments

firmware v1.3.8.3 ( 12/02/2011 )

update content:
WPA-PSK -> WPA-PSK [TKIP]
WEP -> WEP [Shared Key]

Written by microseven

March 27th, 2012 at 4:16 pm

Steps to configure M7-GN2 wireless bridge

without comments

  1. Enter //192.168.1.230 in the browser address bar,go to the following device information page
    M7-GN2 Device Information
  2. Choose Wireless tab to go to current device configuration page
    M7-GN2 Wireless Setup
    1. Wireless Mode, pull drop list and select ‘Access Point WDS’
    2. In WDS Peers, enter the corresponding MAC address of the remote device(s). If there are several remote devices, enter the MAC address for these several devices.
      The figure is shown there are three slave devices, and MAC are: 00:15:6d:5b:a9:69,00:15:6d:5b:a9:6a and 00:15:6d:5b:a9:6b
    3. Enter SSID
    4. Country Code should be current location. We are in United States, then we select United States
    5. Frequency List, set to Enable, click the Edit button, enter the following page, select Frequency in the list
      M7-GN2 Frequency Select on Wireless Setup
    6. Wireless Security – Security set to ‘None’
    7. Click the Change button to complete the setup
  3. Select the Network, to go to the network configuration page
    M7-GN2 Network Configuration
    1. Network Mode to set to ‘Bridge'(Attention: must not be set to ‘Router’)
    2. Bridge IP Address to set to ‘Static’
    3. Device default IP Address is 192.168.1.230. It can be modified by new IP address.
    4. Enter Netmask, Gateway IP
    5. Click on ‘Change’ to complete the set up.
  4. Repeat 2-3,complete other three slave devices Wireless and Network set up
    Three slave devices, the IP Addresses are 192.168.1.232, 192.168.1.232, 192.168.1.233
    ***Attention: master and slave devices IP address should be on the same network segment
    M7-GN2 Master Slaves Configuration

M7-GN2 setup guidelines
M7GN2 setup step 1
M7GN2 setup step 2
M7GN2 setup step 3

Written by microseven

January 23rd, 2012 at 11:54 pm

Posted in Hardware Repairing,How To

Tagged with ,

M7-PTZDWS-22X optional zoom PTZ network camera OSD menu info

without comments

This post is only for optional zoom PTZ network camera OSD menu info.
You may help OSD menu – M7-PTZDWS-22X, the following snapshot will help to use OSD menu.
Preset number of OSD menu is 57.
You input 57 on preset number field, then click on RECALL button, then OSD menu will pop up.
After popup console menu on OSD. You will find control button assicioate with control of OSD menu.

@microseven

Written by microseven

July 21st, 2011 at 1:21 am

iPad and iPhone app to view M7LIVE flash streaming video – iswifter

without comments

Go to App Store, search for iswifter
To get it installed.
Notes: you do not have to subscriber it. This program is to make Flash video display on iPad, iPhone.
I have snapshots attached, may help you.

URL for your iPad is
http://www.microseven.com/users/danapointcam.html

Support
Microseven

Written by microseven

July 12th, 2011 at 2:09 pm

Sonicwall router/firewall will block video streaming

without comments

Any Sonicwall router/firewall will block video streaming. If you have such firewall, you need to install camera(s) outside your Sonicwall firewall.
Support
Microseven

Written by microseven

July 12th, 2011 at 2:02 pm

Microseven M7CMS Full version 3.452 (released on 7/07/2011)

without comments

Microseven M7CMS Full version 3.452 (released on 7/07/2011). Please download and update your previous M7CMS versions.

Written by microseven

July 10th, 2011 at 12:31 am

Posted in Hardware Repairing

Tagged with

M7LIVE 2.06 (streaming video server on microseven.tv) (released on 7/07/2011)

without comments

M7LIVE 2.06 (streaming converter to flash format) (released on 7/7/2011)

Written by microseven

July 10th, 2011 at 12:10 am

Firmware new version released ramdisk-nt3511h-v1.3.8.1

without comments

New firmware has been released version ramdisk-nt3511h-v1.3.8.1 on July 7, 2011

Microseven

Written by microseven

July 10th, 2011 at 12:04 am

Posted in Hardware Repairing

Tagged with

Firmware new version released ramdisk-nt3511h-v1.3.7.9a

without comments

New firmware has been released version ramdisk-nt3511h-v1.3.7.9a on March 7, 2011

1. Fixed bug in 4-ports digital video server PTZ cruise and image quality display.
2. Fixed bug in 4-ports digital video server video shield, motion detection image display
3. HD network camera -> video shield setting bug fixed.

Microseven

Written by microseven

March 7th, 2011 at 3:15 pm

Posted in Hardware Repairing

Tagged with